Information
New Cisco IP Phone Power Injector For 7900 Series Phones CP-PWR-INJ
Specification
[Anchor]
Description
[Anchor]
Dimensions (H x W x D)
[Anchor]
1.6 x 4.6 x 5.45 in. (4.1 x 11.8 x 13.8 cm)
[Anchor]
Weight
[Anchor]
.66 lb (.30 kg)
[Anchor]
Phone casing composition
[Anchor]
Polycarbonate acrylonitrile butadiene styerene (ABS) plastic in textured dark gray color
[Anchor]
Power requirements
[Anchor]
Power is integrated (see Table 5 for country-specific power cords used for connection to AC wall outlet)
[Anchor]
Part number
[Anchor]
CP-PWR-INJ
[Anchor]
LAN connection
[Anchor] • Maximum Ethernet cable length: 100 m from switch to device [Anchor] • Type: RJ-45 [Anchor] • Label: DATA -Network
[Anchor]
Device connection
[Anchor] • Maximum Ethernet cable length: 100 m from switch to device [Anchor] • Type: RJ-45 [Anchor] • Label: DATA and PWR -PHONE
[Anchor]
LEDs
[Anchor]
Two-"Power" and "Status"
[Anchor]
Stackable
[Anchor]
Yes-Two injectors can be stacked
[Anchor]
Wired pairs used
[Anchor]
Injects power into two unused pairs in the Ethernet cable: 4 and 5 (negative) and 7 and 8 (positive)
[Anchor]
Electrical
[Anchor]
Input:
[Anchor] • AC input voltage range: 90 to 264 VAC [Anchor] • AC input current: 0.5A (RMS) @ 90 VAC at maximum load [Anchor] • AC input frequency: 47 to 63 Hz [Anchor] • Maximum inrush current: 20A @ 115 VAC, 60 Hz, Cold Start, 25°C
40A @ 230 VAC, 50 Hz, Cold Start, 25°C [Anchor]
Output:
[Anchor] • DC output voltage: 48 VDC nominal [Anchor] • Maximum output power: 15.5W @ 48 VDC [Anchor]
Performance efficiency:
[Anchor] • 53% minimum at 30-49% of maximum load and 120 VAC, 60 Hz [Anchor] • 75% minimum at 50-100% of maximum load and 120 VAC, 60 Hz[Anchor]TEMPERATURE[Anchor] Table 2 gives temperature ratings for the Cisco Unified IP Phone Power Injector. [Anchor]Table 2. Temperature Ratings for Cisco Unified IP Phone Power Injector[Anchor][Anchor]
Temperature Variable
[Anchor]
Description
[Anchor]
Operating temperature
[Anchor]
32 to 104°F (0 to 40°C)
[Anchor]
Relative humidity
[Anchor]
10 to 95% (noncondensing)
[Anchor]
Storage temperature
[Anchor]
14 to 140°F (-10 to 60°C)
New Cisco IP Phone Power Injector For 7900 Series Phones CP-PWR-INJ
Model: CP-PWR-INJ=
P/N: 800-27212-02
New Sealed
Included:
-
1 x New Cisco IP Phone Power Injector For 7900 Series Phones CP-PWR-INJ= 800-27212-02
Description:
The Cisco Unified IP Phone Power Injector is a midspan power injector designed and tested for use with Cisco Unified IP phones. The Cisco Unified IP Phone Power Injector sits between a switch port and the Cisco Unified IP phone, providing inline power capability to an unpowered switch port. It supports Cisco midspan power, IEEE 802.3af modes for supplying power to the attached phone, and 10/100/1000BASE-T Ethernet connections. Figure 2 shows the maximum distance of the Cisco Unified IP Phone Power Injector between a Cisco Unified IP phone and an Ethernet switch.
Figure 2. Network Diagram
FEATURES
The Cisco Unified IP Phone Power Injector offers several features, including:
• A desktop and desk-area single-port midspan injector with integrated power
• 802.3af/IEEE Power over Ethernet (PoE) support
• Gigabit Ethernet support
• Full enterprise-level compliance
• Designed and tested for use with Cisco Unified IP Phones
SPECIFICATIONS
Table 1 lists specifications of the Cisco Unified IP Phone Power Injector.
Table 1. Specifications of the Cisco Unified IP Phone Power Injector
Specification
[Anchor]
Description
[Anchor]
Dimensions (H x W x D)
[Anchor]
1.6 x 4.6 x 5.45 in. (4.1 x 11.8 x 13.8 cm)
[Anchor]
Weight
[Anchor]
.66 lb (.30 kg)
[Anchor]
Phone casing composition
[Anchor]
Polycarbonate acrylonitrile butadiene styerene (ABS) plastic in textured dark gray color
[Anchor]
Power requirements
[Anchor]
Power is integrated (see Table 5 for country-specific power cords used for connection to AC wall outlet)
[Anchor]
Part number
[Anchor]
CP-PWR-INJ
[Anchor]
LAN connection
[Anchor] • Maximum Ethernet cable length: 100 m from switch to device [Anchor] • Type: RJ-45 [Anchor] • Label: DATA -Network
[Anchor]
Device connection
[Anchor] • Maximum Ethernet cable length: 100 m from switch to device [Anchor] • Type: RJ-45 [Anchor] • Label: DATA and PWR -PHONE
[Anchor]
LEDs
[Anchor]
Two-"Power" and "Status"
[Anchor]
Stackable
[Anchor]
Yes-Two injectors can be stacked
[Anchor]
Wired pairs used
[Anchor]
Injects power into two unused pairs in the Ethernet cable: 4 and 5 (negative) and 7 and 8 (positive)
[Anchor]
Electrical
[Anchor]
Input:
[Anchor] • AC input voltage range: 90 to 264 VAC [Anchor] • AC input current: 0.5A (RMS) @ 90 VAC at maximum load [Anchor] • AC input frequency: 47 to 63 Hz [Anchor] • Maximum inrush current: 20A @ 115 VAC, 60 Hz, Cold Start, 25°C
40A @ 230 VAC, 50 Hz, Cold Start, 25°C [Anchor]
Output:
[Anchor] • DC output voltage: 48 VDC nominal [Anchor] • Maximum output power: 15.5W @ 48 VDC [Anchor]
Performance efficiency:
[Anchor] • 53% minimum at 30-49% of maximum load and 120 VAC, 60 Hz [Anchor] • 75% minimum at 50-100% of maximum load and 120 VAC, 60 Hz[Anchor]TEMPERATURE[Anchor] Table 2 gives temperature ratings for the Cisco Unified IP Phone Power Injector. [Anchor]Table 2. Temperature Ratings for Cisco Unified IP Phone Power Injector[Anchor][Anchor]
Temperature Variable
[Anchor]
Description
[Anchor]
Operating temperature
[Anchor]
32 to 104°F (0 to 40°C)
[Anchor]
Relative humidity
[Anchor]
10 to 95% (noncondensing)
[Anchor]
Storage temperature
[Anchor]
14 to 140°F (-10 to 60°C)
VAT IS NOT PAYABLE BY PURCHASERS OUTSIDE OF THE UK
CS 10024 -100
Specifications
-
GTIN:5054484050483
To request a price please fill out the form below...
Close