Supermicro SuperChassis CSE-826 2 Eight-Core XEON E5-2660 24GB 2U Server

Supermicro SuperChassis CSE-826 2 Eight-Core XEON E5-2660 24GB Rack Server

Chassis Part number: SC826BE1C-R920LPB

Motherboard Part number: X9DRi-LN4F+

In good condition and in full working order

Specifications

• Processor - 2 x Intel 8-Core XEON E5-2660 2.2GHz Processors
• Memory - 24GB Ram
• 12 x 3.5" SATA drive caddies
• 2 x LSI MegaRAID SAS3081E-R RAID 0, JBOD, RAID 1, RAID 10E, RAID 1E controller cards (1 runs 8 drives and the other runs 4)
• Upgrade to Adaptec ASR 71605 1GB Cache 6GBps Battery backed RAID Controller which supports RAID Levels 0, 1, 1E, 5, 6, 10, 50, 60 and will run all 12 drives available @ £240
• 920W 80 Plus Platinum Power Supply
• Rack Rails aren't not included, available @ £66

 

Manufacturer's full spec

Key Features 1. Dual socket R (LGA 2011) supports Intel® Xeon® processor E5-2600 and E5-2600 v2 family† 2. Intel® C602 chipset; QPI up to 8.0GT/s 3. Up to 1.5TB ECC DDR3, up to 1866MHz; 24x DIMM slots * Depends on memory configuration 4. Expansion slots: 4 x16 PCI-E 3.0, 1 x8 PCI-E 3.0, 1 x4 PCI-E 3.0 (in x8) 5. 4x Gigabit Ethernet LAN ports; Intel® i350 GbE controller 6. 8x SATA2 and 2x SATA3 ports 7. Integrated IPMI 2.0 and KVM with Dedicated LAN 8. 9x USB 2.0 ports (4 rear, 4 via header + 1 Type A)

Product SKUs MBD-X9DRi-LN4F+ -B X9DRi-LN4F+ (Bulk Pack) Physical Stats Form Factor Enhanced Extended ATX Dimensions 13.68" x 13" (34.7cm x 33cm) Processor/Cache CPU Dual Socket R (LGA 2011) Intel® Xeon® processor E5-2600 and E5-2600 v2 family† (up to 135W TDP **) Note † BIOS version 3.0 or above is required Note ** Motherboard supports this maximum TDP. Please verify your system can thermally support. Cache Up to 30MB System Bus QPI up to 8 GT/s System Memory Memory Capacity 24x 240-pin DDR3 DIMM slots Up to 1.5TB DDR3 ECC LRDIMM Up to 768GB DDR3 ECC RDIMM Up to 128GB DDR3 ECC/non-ECC UDIMM Memory Type 1866/1600/1333/1066/800MHz* ECC DDR3 SDRAM 72-bit, 240-pin gold-plated DIMMs Support ECC and non-ECC UDIMMs * Maximum memory speed may be capped by CPU. Please verify that the chosen CPU can support desired memory speed. DIMM Sizes 32GB, 16GB, 8GB, 4GB, 2GB, 1GB, 64GB LRDIMM Memory Voltage 1.5 V, 1.35 V Error Detection Corrects single-bit errors Detects double-bit errors (using ECC memory) On-Board Devices Chipset Intel® C602 chipset AHCI SATA SATA 2.0 3Gbps with RAID 0, 1, 5, 10 SATA 3.0 6Gbps with RAID 0, 1, 5, 10 SCU SATA SATA 2.0 3Gbps with RAID 0, 1, 5, 10 IPMI Support for Intelligent Platform Management Interface v.2.0 IPMI 2.0 with virtual media over LAN and KVM-over-LAN support Nuvoton WPCM450 BMC Network Controllers Intel® i350 Gigabit Ethernet (x4 ports) Virtual Machine Device Queues reduce I/O overhead Supports 10BASE-T, 100BASE-TX, and 1000BASE-T, RJ45 output 1x Realtek RTL8201N PHY (dedicated IPMI) Video Matrox G200eW Input / Output AHCI SATA 2x SATA 3.0 ports (6Gbps) 4x SATA 2.0 ports (3Gbps) SCU SATA 4x SATA 2.0 ports (3Gbps) LAN 4 RJ45 Gigabit Ethernet LAN ports 1 RJ45 Dedicated IPMI LAN port USB 9 USB 2.0 ports total (4 rear + 4 via header + 1 Type A) Video 1 VGA port Serial Port / Header 2 Fast UART 16550 ports: 1 rear and 1 header DOM 1 DOM (Disk on Module) power connector TPM 1 TPM Header Expansion Slots PCI-Express 4 (x16) PCI-E 3.0 slots 1 (x8) PCI-E 3.0 slot 1 (x4) PCI-E 3.0 (in x8) slot (Both CPUs need to be installed for full access to PCI-E slots and onboard controllers. See manual block diagram for details.) System BIOS BIOS Type 128Mb SPI Flash EEPROM with AMI BIOS BIOS Features Plug and Play (PnP) APM 1.2 PCI 2.3 ACPI 1.0 / 2.0 / 3.0 / 4.0 USB Keyboard support SMBIOS 2.7.1 UEFI 2.3.1 Management Software SuperDoctor® III Watch Dog NMI IPMI 1.5 / 2.0 Power Configurations ACPI / APM Power Management Power-on mode for AC power recovery PC Health Monitoring Voltage Monitors for CPU Cores, +1.1V, +1.5V, +3.3V, +5V, +12V, +3.3V Standby, +5V Standby, VBAT, Memory Voltages. 6+1 Phase-switching voltage regulator FAN 8x 4-pin fan headers (up to 8 fans) 8x fans with tachometer monitoring Status monitor for speed control Pulse Width Modulated (PWM) fan connectors Temperature Monitoring for CPU and chassis environment CPU thermal trip support Thermal Control for 8x Fan Connectors Thermal Monitor 2 (TM2) support PECI LED CPU / System Overheat LED Suspend static indicator LED UID/Remote UID Other Features Chassis intrusion detection Chassis intrusion header RoHS, Halogen Free Operating Environment Operating Temperature Range 10°C - 35°C (50°F - 95°F) Non-Operating Temperature Range -40°C - 70°C (-40°F - 158°F) Operating Relative Humidity Range 8% - 90% (non-condensing) Non-Operating Relative Humidity Range 5% - 95% (non-condensing)